Featuring A Couple of Craft Addicts!!! Ruffled Keyhole Shirt Tutorial…

October 27, 2011 5 Comments



Today I have the honor of introducing Jessica, one of the members of the team from A Couple of Craft Addicts! Heather and Jessica are the two mega-minds behind their site, and they both share a deep passion for all things crafty (hence – their name…lol).

Jessica is the seamstress between the two having sewn since High School, and as most home bloggers will say, fell in love with the art again once her kids were born! And we can all be thankful that she did, just look at some of the projects this tag-team duo comes up with….




How cute is that?!! I had to throw in the Jack Sparrow hair tutorial…with Halloween around the corner, it is simply GENIUS! (Click on the picture above to take you to any of the posts directly).

Thank you so much for being here Jessica, and sharing your love of sewing with us. I absolutely L-O-V-E what you made! So without further ado, I give you Jessica from A Couple of Craft Addicts!

———————————————————————

Have you seen this dress from Mod Clothing?

I just love it. I love the neckline, I love all the embellishment details around the neck and hemline. I love the color. I was so inspired by this dress that I decided to make a similar top for my daughter. I wanted to try something new. I wanted to push myself and my machine.

I have not sewed much with embroidery stitches so this was the perfect project to experiment.

Want to make one? Don't be afraid of the details, we are all learning here.

Here is the full tutorial so you can make your own.

Supplies:
1/2 yard of fabric (I used basic quilting cotton, this is for a 2T)
1/4-1/2 yard of trim for ruffles, back panel, and bias tape if you want to make your own or you can buy a pack.
4-5 large buttons
1 small button
Your sewing machine and thread

1. Begin by cutting out your pattern. You can do this by tracing a shirt that fits your model. I always use a shirt that is a little loose. Fold the shirt in half and trace from the neckline, under the arm pit, and down the sides. Continue down until it is the length you want. You will be adding bias tape to the bottom so you don't need to leave room for a hem. Then trace the sleeve, I extended mine to make a longer sleeve.

Then cut out of your pattern. Two sleeves on the fold and two bodices on the fold. I cut the neck of the front a little deeper than the back. You will also need to cut the following from your trim fabric.

- 2 strips 2 inches wide (I used about 62 inches total) for the ruffles

-2 4inch strips the length of the back of your top for the button tab

-bias tape for the neck, keyhole, arm bands, and bottom hem

2. Lay the front of your shirt down and cut out your keyhole. I just drew mine with a fabric pencil. Then I folded the shirt in half and cut it to make sure the sides were equal.

3. Now we are going to create the ruffles. Take one of your long 2inch wide strips and sew a loose stitch down the side about 1/4 inch from the edge, leaving the end long for gathering. But before you gather, stitch the wide side with a zig zag or other stitch of your choice. This will close the edge to prevent fraying and add some contrast to the ruffle. Then you can gather the piece creating a loose ruffle. Finally I pressed the ruffle flat with my iron. Repeat with the other strip.


4. Now you are going to pin your ruffle in place. Start with the top ruffle which will be right around the keyhole. Pin it in place and stitch it down (I try to stitch on my gather stitches).

Next you will pin the second layer down. Place the end right next to the seam of the top ruffle but underneath. Then pin in place with the ruffle edge matching up with the first ruffle seam. (Aren't pictures great lol) Sew that ruffle down.

Finally pin the third ruffle under the second ruffle the same way. This time fold the end of the ruffle to make sure it lines up with the neck not the shoulder. Pin in place and stitch it down.

The final step to the ruffle is adding the bias tape around the keyhole cut out. Pin in place and sew it down.

5. Now we are going to work on the back. Lay your back piece flat. Cut down the middle so you have two pieces. (You could also cut the back piece on the edge instead of the fold). Now cut 1/2 inch off the edge to make room for the panel.

Next take your panel pieces and press them in half so you have 2 inch pieces. Match up the raw edges and right sides together. Pin in place and sew down. Repeat with the other side. Then press them open.

6. Now we are going to put our pieces together. (Still with me?) With the right sides facing match up the shoulders, pin together, and stitch (make sure to finish off your edges by serge or zig zag).

Then you are going to add your bias tape to the neckline. You will need to finish your edges by folding right sides together, stitch and back stitch, and flip. For more information on this check out this tutorial. Use a lot of pins to hold it in place and then stitch down. The tricky part is the keyhole. You will just go straight across, try to keep the tips of the keyhole close but not overlapping.

7. Now we are going to add the sleeves. On the end of the sleeve add bias tap to finish off the edge.

Then with right sides facing place the sleeve in the arm holes pinning it in place. Sew it down, finished your edges, and repeat with the other side.

You end up with this.

YOU'RE ALMOST DONE!

8. Turn your shirt inside out and with right sides together pin and sew up the sides.

Turn right side out. Now you have a shirt; just need to add the buttons and finish the bottom.

If you are using a button foot on your machine now is the time to apply what you know or get out the manual. Here is how I do mine. Place your buttons where you want them and use a fabric pencil to mark the bottom edge.

Sew your button holes, use the seam ripper to cut the holes, and sew your buttons to the under side.

You also need to sew your small button to the front in between the tips of the keyhole. This covers the blank area.

9. Now you are going to add the bias tape to the bottom. You will need to finish off the edges just as before and pin it in place. Stitch it down. Then if you want you can add the embroidery stitch to the hemline. I think it adds some interest and fun.

Now you are done. I know there were a lot of pictures but that's how I operate. I hope you enjoyed it and make one of your own.


Thanks Jessica for having me guest post. I just love how we can share our ideas and knowledge through the digital world.

--------------------------------------------------------------


Thank you again so much for being here Jessica! I absolutely adore this shirt! And PS - what is the name of that fabric?!! LOVE IT!!!

Be sure to head on over to A Couple of Craft Addicts and check out there site! You won't be disappointed :)

Want to be featured on Me Sew Crazy?
Drop me an e-mail with your idea at jgerblick@hotmail.com

Thanks so much for stopping by, and until next time...Happy Sewing!

Filed Under: A Couple of Craft Addicts, feature

Comments

  1. Emily says:
    October 27, 2011 at 3:47 pm

    Darling! Love the contrasting fabric on the button placket.

    Reply
  2. Marie chavez says:
    October 27, 2011 at 9:20 pm

    Love it. I will start on one for my baby today…

    Reply
  3. Kelli says:
    November 5, 2011 at 5:02 am

    This is so stinkin’ cute! Thanks for the tutorial! I can’t wait to make one!

    Reply
  4. Jennifer says:
    November 27, 2011 at 3:42 am

    I love this shirt!!! Thanks so much for sharing. I can’t wait to try it out.

    Reply
  5. Mama G says:
    December 15, 2011 at 12:38 am

    Thank you! This is a beautiful shirt, and I just finished one for my daughter =) Great tutorial.

    Reply

Leave a Comment

*